PolySonic™ PLA Pro

TDS PDF 다운로드

PolySonic™ PLA PRO는 매우 빠른 속도로 출력할 수 있는 고인성 PLA입니다. 고급 포뮬러를 바탕으로 ABS에 가까운 충격 강도와 ASA·PETG를 넘어서는 굽힘 강도를 제공해, 빠르게 기능성 부품을 만들어야 할 때 잘 맞습니다.

물리적 물성

Property	Testing Method	Typical Value
Density	ISO1183, GB/T1033	1.23g/cm3 at 21.5°C
Melt index	210°C	15.5 g/10min
Light transmission	N/A	N/A
Flame retardancy	N/A	N/A

화학 저항 데이터

Property	Typical Value
Effect of weak acids	Good
Effect of strong acids	Poor
Effect of weak alkalis	Fair
Effect of strong alkalis	Poor
Effect of oils and grease	Good

참고:

Good: 상온에서 장시간 접촉해도 경미한 영향만 받을 수 있습니다.

Fair: 상온에서 짧은 시간 접촉은 가능합니다.

Poor: 상온에서 접촉 시 소재가 불안정해질 수 있습니다.

열적 특성

Property	Testing Method	Typical Value
Glass transition temperature	DSC, 10°C/min	61 °C
Melting temperature	DSC, 10°C/min	164 °C
Crystallization temperature	DSC, 10°C/min	96 °C
Decomposition temperature	TGA, 20°C/min	370 °C
Vicat softening temperature	ISO 306, GB/T 1633	61 °C
Heat deflection temperature	ISO 75 1.8MPa	52 °C
Heat deflection temperature	ISO 75 0.45MPa	55 °C

기계적 물성 – 일반 속도

Property	Testing Method	Typical Value
Young’s modulus (X-Y)	ISO 527, GB/T 1040	2360.0 ± 30.1 MPa
Young’s modulus (Z)	ISO 527, GB/T 1040	2283.3 ± 32.1 MPa
Tensile strength (X-Y)	ISO 527, GB/T 1040	41.2 ± 0.6 MPa
Tensile strength (Z)	ISO 527, GB/T 1040	33.6 ± 0.5 MPa
Elongation at break (X-Y)	ISO 527, GB/T 1040	23.4 ± 6.3 %
Elongation at break (Z)	ISO 527, GB/T 1040	4.9 ± 1.1 %
Bending modulus (X-Y)	ISO 178, GB/T 9341	2688.7 ± 26.1 MPa
Bending modulus (Z)	ISO 178, GB/T 9341	N/A
Bending strength (X-Y)	ISO 178, GB/T 9341	67.5 ± 0.7 MPa
Bending strength (Z)	ISO 178, GB/T 9341	N/A
Notched Charpy impact strength (X-Y)	ISO 179, GB/T 1043	22.7 ± 2.5 kJ/m2
Notched Charpy impact strength (Z)	ISO 179, GB/T 1043	N/A

• 0.4 mm 노즐, 0.2mm 레이어 높이 기준입니다. 일반 출력 속도 = 46.7mm/s, 출력 온도 = 210 °C

기계적 물성 – 고속

Property	Testing Method	Typical Value
Young’s modulus (X-Y)	ISO 527, GB/T 1040	2305.7 ± 42.9 MPa
Young’s modulus (Z)	ISO 527, GB/T 1040	2102.9 ± 74.3 MPa
Tensile strength (X-Y)	ISO 527, GB/T 1040	39.3 ± 0.5 MPa
Tensile strength (Z)	ISO 527, GB/T 1040	31.9 ± 0.5 MPa
Elongation at break (X-Y)	ISO 527, GB/T 1040	17.9 ± 5.2 %
Elongation at break (Z)	ISO 527, GB/T 1040	3.8 ± 0.2 %
Bending modulus (X-Y)	ISO 178, GB/T 9341	2544.5 ± 27.0 MPa
Bending modulus (Z)	ISO 178, GB/T 9341	N/A
Bending strength (X-Y)	ISO 178, GB/T 9341	64.1 ± 0.6 MPa
Bending strength (Z)	ISO 178, GB/T 9341	N/A
Notched Charpy impact strength (X-Y)	ISO 179, GB/T 1043	19.4 ± 3.4 kJ/m2
Notched Charpy impact strength (Z)	ISO 179, GB/T 1043	N/A

• 0.4 mm 노즐, 0.2mm 레이어 높이 기준입니다. 고속 출력 = 300mm/s, 출력 온도 = 230 °C

권장 출력 조건

Parameter
Nozzle temperature	Classic :190-210 °C High-speed: 210-230 °C
Build surface treatment	PC and Texture PEI (Glue when needed)
Build plate temperature	30 - 60 (˚C)
Cooling fan	ON
Printing speed	Classic :50-100mm/s High-speed: 100-300mm/s
Retraction distance	1 - 3 (mm)
Retraction speed	20 - 40 (mm/s)
Closure Chamber	No Needed
Recommended support material	PolySupport™ and PolyDissolve™ S1
Drying setting	55˚C for 6h

• 0.4 mm 노즐 기준입니다. 노즐 직경이 달라지면 출력 조건도 달라질 수 있습니다.

인장 시험 시편

ISO 527, GB/T 1040

굽힘 시험 시편

ISO 178,GB/T 9341

충격 시험 시편

ISO 179,GB/T 1043

시편 제작 조건

Printing temperature	210°C/230°C
Bed temperature l	50°C
Shel	2
Top& bottom layer	3
Infill	100%
Environmental temperature	Ambient temperature
Cooling fan	ON

면책 고지

The typical values presented in this data sheet are intended for reference and comparison purposes only. They should not be used for design specifications or quality control purposes. Actual values may vary significantly with printing conditions. End- use performance of printed parts depends not only on materials, but also on part design, environmental conditions, printing conditions, etc. Product specifications are subject to change without notice.

Each user is responsible for determining the safety, lawfulness, technical suitability, and disposal/ recycling practices of Polymaker materials for the intended application. Polymaker makes no warranty of any kind, unless announced separately, to the fitness for any use or application. Polymaker shall not be made liable for any damage, injury or loss induced from the use of Polymaker materials in any application.