> For the complete documentation index, see [llms.txt](https://wiki.polymaker.com/llms.txt). Markdown versions of documentation pages are available by appending `.md` to page URLs; this page is available as [Markdown](https://wiki.polymaker.com/polymaker-wiki/polymaker-wiki-zh/da-yin-ji-qiao/chang-jian-da-yin-wen-ti/curling-of-layers-and-angles.md).

# 层与角度卷曲

这个问题看起来很像翘曲（warping），但与模型从打印底板上翘起不同，它是指单个层似乎向上卷曲，我们称之为“翘曲（curling）”。你会发现，解决此问题的方案与“[翘曲](https://us.polymaker.com/blogs/3d-printing-tips/warping)”页面中给出的方案几乎完全相反，因为这种卷曲问题实际上与翘曲没有任何关系。

<figure><img src="https://1102955884-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FA2YI9GFoVmpURdSqt1Vr%2Fuploads%2Fgit-blob-45f7773cd9786cbf451a6a57c97693dee3c58be6%2Fimage%20(29).png?alt=media" alt=""><figcaption></figcaption></figure>

### **开启主动冷却风扇**

当使用 PLA 且未开启主动冷却风扇或风扇转速不足时，最常出现卷曲问题。PLA 的最佳打印效果通常要求在第一层打印完成后，将冷却风扇开启至 100% 的功率。

**视觉证据**\
提供的对比图展示了使用相同设置打印的 PLA 模型：

* **左侧打印件：** 无主动冷却风扇
* **右侧打印件：** 第一层后风扇转速 100%

**关键因素**

* **材料特性：** PLA 的快速固化得益于强制冷却
* **层间附着力：** 受控的冷却可防止结晶过程中的翘曲
* **质量保证：** 持续的风扇开启可保持尺寸精度

**实施指南**

* **第一层协议：** 在初始层沉积期间禁用冷却
* **风扇加速：** 在第二层初始化期间逐渐提高风扇转速
* **硬件验证：** 在长时间打印前确认风扇功能正常

![](https://cdn.shopify.com/s/files/1/0548/7299/7945/files/Curling_600x600.png?v=1711482250)

主动冷却风扇虽然对某些材料的层间附着力可能有负面影响，但对于 PLA 打印仍然至关重要。在 PLA 沉积过程中缺乏主动冷却，会导致表面缺陷和顶层卷曲。

**材料特定指南**

* **PLA 要求：** 必须开启主动冷却以获得最佳表面光洁度
* **通用协议：** 请查阅制造商规格说明，了解特定耗材的冷却需求

**环境因素**

* **温度敏感性：** 过高的环境热量会加剧卷曲，特别是在封闭式机箱中
* **PLA 机箱使用：** 由于 PLA 的玻璃化转变温度较低（约 60°C），应避免在封闭环境中使用
* **通用机箱规则：** 对于没有翘曲倾向的材料，建议使用开放式机箱配置

**实施策略**

* **通风要求：** 保持 PLA 打印的开放空气环境
* **机箱管理：** 在 PLA 沉积期间取下盖子/打开机门
* **热监测：** 确认机箱温度保持在材料特定阈值以下

**技术原理**

* **结晶控制：** 强制冷却加速 PLA 固化
* **防止翘曲：** 环境温度调节可保持尺寸稳定性
* **材料兼容性：** 与 PLA 不同，高温材料（如 ABS）通常需要封闭式机箱

### **层冷却时间不足**

如果你正在打印模型中较小的部分，且每一层都在短时间内连续堆叠，那么前一层可能没有足够的时间冷却。这就是 Cura 中“冷却”部分存在“最小层时间（Minimum Layer Time）”设置的原因。

![](https://cdn.shopify.com/s/files/1/0548/7299/7945/files/Cura_600x600.png?v=1711482669)

**层时间管理**\
对于大多数材料，3-5 秒的最小层时间非常有效。启用后，如果层完成速度快于设定的持续时间（例如 3 秒），打印机将暂停，从而防止在未冷却的层上过早沉积。将其与 Cura 的“抬升喷头（Lift Head）”功能结合使用，可以在暂停期间通过物理分离喷头与打印件来增强冷却效果。

**层高注意事项**

* **低层高风险：** 较薄的层（例如 0.1mm）比厚层（例如 0.3mm）的刚性更低，增加了卷曲的敏感性
* **解决方案：** 增加层高或打印速度以提高结构稳定性

**温度控制**

* **挤出指南：** 在制造商指定的温度范围内操作
* **小喷嘴协议：** 当使用小于 0.4mm 的喷嘴配合薄层打印时，将温度降低至推荐范围的下限

**支撑结构优化**

* **材料特定角度：**
  * **PLA：** 建议在悬垂角度 ≥55° 时使用支撑
  * **ABS/ASA：** 由于冷却限制，在 ≥45° 时需要支撑
* **原理：** 对易翘曲材料的受限风扇使用，需要更保守的支撑阈值

**材料处理**

* **水分缓解：** 如果在进行其他调整后卷曲仍然存在，则表明耗材可能受潮
* **干燥协议：** 使用耗材干燥机或受控加热环境对线材进行脱水

**实施矩阵**

| 问题      | 解决方案               | 技术原理      |
| ------- | ------------------ | --------- |
| 层打印过快   | 启用 3-5 秒层时间 + 抬升喷头 | 防止热量积聚    |
| 层过薄     | 增加层高/速度            | 增强层刚性     |
| 温度过高    | 降低喷头温度             | 降低材料塑性    |
| 悬垂角度无支撑 | 调整支撑阈值             | 补偿有限的冷却   |
| 水分      | 干燥耗材               | 消除蒸汽引起的翘曲 |

## **减少 3D 打印件层与角度卷曲的方法总结**

* 如果你的材料需要，请确保主动冷却风扇已开启。打印 PLA 时，建议在第一层之后将风扇转速设置为 100%。
* 确保环境空气温度未接近所打印材料的玻璃化转变温度。PLA 不应在完全封闭的机器中打印。
* 在 Cura 中将最小层时间设置为至少 3 秒，以便每一层都有足够的时间冷却。
* 低层高刚性较差，因此增加层高或打印速度会有所帮助。
* 降低打印温度，特别是在使用小直径喷嘴进行低层高打印时。
* 开启支撑结构并减小所需支撑的角度，特别是对于无法使用主动冷却风扇的材料。
* 如果尝试了上述所有方法后仍有问题，请去除材料中的水分。

{% embed url="<https://www.youtube.com/shorts/_t9jQxzJLxg>" %}


---

# Agent Instructions
This documentation is published with GitBook. GitBook is the documentation platform designed so that both humans and AI agents can read, navigate, and reason over technical content effectively. Learn more at gitbook.com.

## Querying This Documentation
If you need additional information that is not directly available in this page, you can query the documentation by asking a question.

Perform an HTTP GET request on the following URL with the `ask` and `goal` query parameters:

```
GET https://wiki.polymaker.com/polymaker-wiki/polymaker-wiki-zh/da-yin-ji-qiao/chang-jian-da-yin-wen-ti/curling-of-layers-and-angles.md?ask=<question>&goal=<user_goal>
```

`ask` is the immediate question: it should be specific, self-contained, and written in natural language.
`goal` is what the user is ultimately trying to achieve, the reason they need the answer. Sharing it helps GitBook give you a better, more relevant answer. A goal is most helpful when it describes the outcome the user wants rather than restating the question. For example, with `ask=how do I create an API token`, a goal like `automate deployments from our CI pipeline` lets GitBook tailor the answer to that use case.

The response will contain a direct answer to the question and relevant excerpts and sources from the documentation.

Use this mechanism when the answer is not explicitly present in the current page, you need clarification or additional context, or you want to retrieve related documentation sections.
