PolyLite™ PLA Pro

Polylite™ PLA Pro is a first of its kind combining high toughness and high rigidity, this professional PLA offers engineering properties with the ease of print of regular PLA.

PHYSICAL PROPERTIES

Property	Testing Method	Typical Value
Density	ISO1183,GB/T1033	1.22 g/cm3 at 21.5℃
Melt index	210℃,2.16kg	6g/10min
Light transmission	N/A	N/A
Flame retardancy	N/A	N/A

CHEMICAL RESISTANCE DATA

Property	Testing Method
Effect of weak acids	Not resistant
Effect of strong acids	Not resistant
Effect of weak alkalis	Not resistant
Effect of strong alkalis	Not resistant
Effect of organic solvent	No data available
Effect of oils and grease	No data available

MOISTURE ABSORPTION CURVE

Property	Testing Method	Typical Value
Glass transition temperature	DSC, 10°C/min	62 °C
Melting temperature	DSC, 10°C/min	150 °C
Crystallization temperature	DSC, 10°C/min	N/A
Decomposition temperature	TGA, 20°C/min	N/A
Vicat softening temperature	ISO 306, GB/T 1633	62.7 °C
Heat deflection temperature	ISO 75 1.8MPa	57.6 °C
Heat deflection temperature	ISO 75 0.45MPa	59.3 °C
Thermal conductivity	N/A	N/A
Heat shrinkage rate	N/A	N/A

Property	Testing Method	Typical Value
Young’s modulus (X-Y)	ISO 527, GB/T 1040	2932.2 ± 55.3 MPa
Young’s modulus (Z)	ISO 527, GB/T 1040	2633.0 ± 117.4 MPa
Tensile strength (X-Y)	ISO 527, GB/T 1040	49.8 ± 0.4 MPa
Tensile strength (Z)	ISO 527, GB/T 1040	36.5 ±0.6 MPa
Elongation at break (X-Y)	ISO 527, GB/T 1040	6.3 ± 0.9 %
Elongation at break (Z)	ISO 527, GB/T 1040	2.4 ± 0.3 %
Bending modulus (X-Y)	ISO 178, GB/T 9341	2933.8 ± 78.3 MPa
Bending modulus (Z)	ISO 178, GB/T 9341	N/A
Bending strength (X-Y)	ISO 178, GB/T 9341	77.9 ± 0.4 MPa
Bending strength (Z)	ISO 178, GB/T 9341	N/A
Charpy impact strength (X-Y)	ISO 179, GB/T 1043	17.1 ±1.2 kJ/m2
Charpy impact strength (Z)	ISO 179, GB/T 1043	N/A

• Based on 0.4 mm nozzle and Simplify 3D v.4.0. Printing conditions may vary with different nozzle diameters

Parameter
Nozzle temperature	190 – 220 (℃)
Build surface material	BuildTak®, Glass, Blue Tape
Build surface treatment	Glue or Magigoo
Build plate temperature	30 - 60 (˚C)
Cooling fan	ON
Printing speed	30-70 (mm/s)
Raft separation distance	0.2 (mm)
Retraction distance	1 - 3 (mm)
Retraction speed	30 - 60 (mm/s)
Environmental temperature	0 - 40 (˚C)
Threshold overhang angle	60 (˚)
Recommended support material	PolySupport™ and PolyDissolve™ S1

TENSILE TESTING SPECIMEN

ISO 527, GB/T 1040

FLEXURAL TESTING SPECIMEN

ISO 178,GB/T 9341

IMPACT TESTING SPECIMEN

ISO 179,GB/T 1043

*All specimens were conditioned at room temperature for 24h prior to testing

Printing temperature	210 °C
Bed temperature	25 °C
Shell	2
Top & bottom layer	4
Infill	100 %
Environmental temperature	25 ˚C
Cooling fan	ON

DISCLAIMER:

The typical values presented in this data sheet are intended for reference and comparison purposes only. They should not be used for design specifications or quality control purposes. Actual values may vary significantly with printing conditions. End- use performance of printed parts depends not only on materials, but also on part design,environmental conditions, printing conditions, etc. Product specifications are subject to change without notice.

Each user is responsible for determining the safety, lawfulness, technical suitability, and disposal/ recycling practices of Polymaker materials for the intended application. Polymaker makes no warranty of any kind, unless announced separately, to the fitness for any use or application. Polymaker shall not be made liable for any damage,injury or loss induced from the use of Polymaker materials in any application.